2017+ Honda Civic Type-R FK8 Turbocharger Inlet Pipe Kit

2017+ FK8 Honda Civic Type-R Turbocharger Inlet Pipe Kit

The PRL Motorsports Turbocharger Inlet Crossover Pipe Kit is a direct bolt-on upgrade that eliminates airflow restriction before the turbocharger, allowing the turbocharger to operate more efficiently. Our design utilizes a cast aluminum inlet piece to allow smooth transition from the gasket-matched 64mm ID compressor inlet to a 78mm ID oulet throughout the titanium crossover pipe. This kit offers a 56% increase in airflow volume in comparison to the factory inlet pipe!

Compatible with factory intake system, factory location intake systems and PRL Motorsports High Volume Intake System.

Kit Includes:

  • Cast aluminum inlet piece
  • Titanium Crossover pipe
  • High-temp 4-ply silicone coupler(s)
  • 304 stainless steel interlocking worm clamps

Pricing and availability of this kit will be announced via our social media as we progress forward with material sourcing and revisions. A rough time frame on having this product to market is approximately Fall 2019.

Testing Car:
Shop 2017 Honda Civic Type-R
KTuner (“Stock” Map and Stage 1 Map tested) on 93 Octane pump gas
PRL Motorsports Turbocharger Inlet Pipe
PRL Motorsports High Volume Intake System
PRL Motorsports Intercooler
PRL Motorsports Race Downpipe / Front Pipe Combo
GReddy Supreme Catback Exhaust System

As per our usual testing methods, we chose to use KTuner’s “Stock” mapping and Stage 1 mapping to provide data/results that the average customer can expect to see without custom tuning. These runs are be compared to the same vehicle with same modifications aside from the Turbocharger Inlet Pipe in identical weather conditions. All runs were started at identical run conditions such as coolant temp and air temp. The results are as follows:

Stock Map:

Inlet%20Pipe%20Stock%20Tune_zps0csfriyq.jpg

Very minor gains at peak (1 horsepower and 3 ft/lb torque) are seen here when comparing Run 2, however, much larger gains down low can be seen. 15-20 horsepower and 25+ ft/lb torque can be seen from 2700 RPM – 3700 RPM.

Inlet%20Pipe%20Stock%20Tune%202_zpsi37uruex.jpg

Run 4 provides us very similar gains (4 horsepower and 3 ft/lb torque) at peak, but these gains carry much better throughout the rest of the power band here. Again, 20-30 horsepower and 30+ ft/lb torque gains can be seen from 2700 RPM – 3700 RPM.

Stage 1 Map:

Inlet%20Pipe%20Stage%201%20Tune_zps5nmysdxy.jpg

Stage 1 Map testing showed us similar gains to the “Stock” Map. Minor gains at peak (horsepower can be dismissed due to the large dyno spike, but 5 ft/lb torque) can be seen, with gains again from 2700 – 3700 RPM when comparing Run 2.

Inlet%20Pipe%20Stage%201%20Tune%202_zpswlzj6twr.jpg

Again, Run 3 showed us major gains from 2700 RPM – 3800 RPM, with a bit more promise throughout the upper powerband.

In conclusion, notable bottom-end/spool gains have been seen with our Turbocharger Inlet Pipe Kit. We expect these gains to be even greater on the street/track due to increased load. Larger gains can be expected on higher output engines that require more airflow, which is why we primarily designed this product. Cars equipped with a custom tune and/or turbocharger upgrades will benefit from this modification even greater, which leads us into our next test subject…

Oh, and here’s a sneak peak of our Ti Inlet Pipe. Production quality and installed pics coming shortly!

edited-image_zpsxmvgr7w3.png
CTR%20Overpipe%204_zpsirt3qcwn.jpg
CTR%20Overpipe%202_zpsodlvgilt.jpg
CTR%20Overpipe%201.1_zps6rviasya.jpg
CTR%20Overpipe%201.2_zpsygnvbytz.jpg
CTR%20Overpipe%201_zpsvcymb8yo.jpg
CTR%20Overpipe%202.1_zpspjarfqnu.jpg
CTR%20Overpipe%2010_zpsb58d8i3r.jpg
CTR%20Overpipe%208_zpsvlpynn0k.jpg

Take a look at the comparisons to the factory setup!

Overpipe%20Comparison%20to%20stock_zpsy7bzh5sh.jpg
Pipe%20Size%20COmparison%20to%20stock_zpsdmlycksc.jpg
ID%20Comparison%20crossover%20Pipe%203D%20print_zpsw2admf1p.jpg
Turbo%20Connection%20ID%20comparison%20to%20stock_zpsxktzkgyk.jpg
Cast%20Engine%20Bay%20%20shot_zpsuli8tn4z.jpg

Leave a Reply

Your email address will not be published. Required fields are marked *


By submitting this form, you are consenting to receive marketing emails from: PRL Motorsports, 1101 Pontiac Ct, Export, PA, 15632, http://www.prlmotorsports.com. You can revoke your consent to receive emails at any time by using the SafeUnsubscribe® link, found at the bottom of every email. Emails are serviced by Constant Contact